MONOline gas detector
MONOLINE Gas Detector
- The MONOline gas warning device is used to display the measured gas concentrations and control the connected devices
- The MONOline is calibrated at the factory and ready for immediate use
- Various sensor technologies available (electrochemical, pellistor and infrared)
- Suitable for 24 VDC or 230 V mains connection
- Wall mounting
- Integrated alarm horn
- Integrated power LED flash light
- Clear display of gas concentration and alarm status on OLED display
- Robust IP65 housing
- 3 programmable relay outputs for controlling alarm components or a ventilation system
- Different relay functions (RESET holding or resetting, normally closed or normally open),
- Programmable switch-on and switch-off delay and alarm limit values
- User-friendly programming with magnetic pen
- Built-in replaceable measuring element
- Integrated MODBUS-RTU interface
- Connection for external reset button
- Swiss quality product
Gas measuring transmitter 4-20 mA
- The gas measuring transmitter is used to monitor the desired gas concentration
- Various sensor technologies available (electrochemical, semiconductor, pellistor and infrared)
- Linear and temperature-compensated 4-20mA output signal
- 16...30 VDC supply voltage (2-wire or 3-wire supply line)
- The gas measuring transmitters are calibrated in the factory to the desired measuring range and supplied with a calibration certificate
- All potentiometers and measuring device connections for calibration are accessible from the outside and it is not necessary to open the gas measuring transmitter
- Robust housing (protection class IP 65)
- Stainless and acid-resistant steel housing
- Swiss quality product
Gas measurement transmitter with digital output
- The KSxC gas measuring transmitter is used to monitor the desired gas concentration
- The gas measurement transmitter is a member of the KIMESSA CANline BUS network, which enables the connection of up to 128 gas sensors and alarm components
- Linear and temperature-compensated digital CANline BUS output signal 16...30 VDC supply voltage (4-wire)
- Various sensor technologies available (electrochemical, semiconductor, pellistor and infrared)
- The gas measuring transmitters are calibrated in the factory to the desired measuring range and supplied with a calibration certificate
- All potentiometers and measuring device connections for calibration are accessible from the outside and it is not necessary to open the gas measuring transmitter
- Robust housing (protection class IP 65)
- Stainless and acid-resistant steel housing
- Swiss quality product
Gas measuring transmitter with 4-20 mA output for Ex zone 2
- The gas measuring transmitter is used to monitor the desired gas concentration
- Various sensor technologies available (electrochemical, semiconductor, pellistor and infrared)
- Linear and temperature-compensated 4-20mA output signal
- 16...30 VDC supply voltage (2-wire or 3-wire supply line)
- The gas measuring transmitters are calibrated in the factory to the desired measuring range and supplied with a calibration certificate
- All potentiometers and measuring device connections for calibration are accessible from the outside and it is not necessary to open the gas measuring transmitter
- Robust housing (protection class IP 65)
- Stainless and acid-resistant steel housing
- ATEX protection class: Ex II 3G nA IIC T4 Gc
- Swiss quality product
Gas measuring transmitter with digital output for Ex zone 2
- The KSxC gas measuring transmitter is used to monitor the desired gas concentration
- The gas measurement transmitter is a member of the KIMESSA CANline BUS network, which enables the connection of up to 128 gas sensors and alarm components
- Linear and temperature-compensated digital CANline BUS output signal 16...30 VDC supply voltage (4-wire)
- Various sensor technologies available (electrochemical, semiconductor, pellistor and infrared)
- The gas measuring transmitters are calibrated in the factory to the desired measuring range and supplied with a calibration certificate
- All potentiometers and measuring device connections for calibration are accessible from the outside and it is not necessary to open the gas measuring transmitter
- Robust housing (protection class IP 65)
- Stainless and acid-resistant steel housing
- ATEX protection class: Ex II 3G nA IIC T4 Gc
- Swiss quality product
Gas measuring transmitter for Ex zone 1 (4-20 mA output/digital)
- The gas measuring transmitter is used to monitor the desired gas concentration
- The gas measurement transmitter is a member of the KIMESSA CANline BUS network, which enables the connection of up to 128 gas sensors and alarm components
- Linear and temperature-compensated digital CANline BUS output signal or 4-20 mA output signal
- 16...30 VDC supply voltage (2-wire, 3-wire supply line or 4-wire for CANline BUS network)
- Integrated MODBUS-RTU interface (RS485)
- Various sensor technologies available (electrochemical, semiconductor, pellistor and infrared)
- The gas measuring transmitters are calibrated in the factory to the desired measuring range and supplied with a calibration certificate
- Calibration using a digital potentiometer, so it is not necessary to open the sensor
- Robust IP65 housing
- Stainless and acid-resistant steel housing
- Clear presentation of the gas concentration and alarm status on a clear OLED display
- User-friendly programming with magnetic pen
- Optional 3 relay contacts for activating alarm components
- Relay contacts: for different relay functions (RESET holding or resetting, normally closed or normally open)
- Relay contacts: Programmable switch-on and switch-off delay and alarm limit values
- Optionally available with 230V power supply unit for standalone operation
- Simple replacement of used sensors with pre-calibrated sensors possible
- ATEX protection class: II 2G Ex d IIC T4 (semiconductor, pellistor and infrared)
- ATEX protection class: II 2G Ex d ia IIC T4 (electrochemical)
- Swiss quality product
Gas measuring transmitter PSxC®
- The PSxC gas measuring transmitter is used to monitor the desired gas concentration
- The gas measurement transmitter is a participant in the PS 2020 CANBUS network, which enables the connection of up to 32 gas measurement transmitters
- Linear and temperature-compensated digital CANBUS output signal 16...30 VDC supply voltage (4-wire)
- Various sensor technologies available (electrochemical, semiconductor, pellistor and infrared)
- The gas measuring transmitters are calibrated in the factory to the desired measuring range and supplied with a calibration certificate
- Robust housing (protection class IP 65)
- Swiss quality product
Gas measuring transmitter KSXM
- The gas measuring transmitter is used to monitor the desired gas concentration
- Linear and temperature-compensated output signal
- 16...30 VDC supply voltage (4-wire supply line)
- Various sensor technologies individually or combined
- available (electrochemical, semiconductor and pellistor )
- The gas measuring transmitters are adjusted in the factory to the desired
- Measuring range calibrated and supplied with calibration certificate
- All potentiometers and measuring device connections for calibration are accessible from the outside and it is not necessary to open the gas measuring transmitter
- Robust housing (protection class IP 65)
- Stainless and acid-resistant steel housing
- MODBUS RTU output
- Used sensors can be easily replaced with
pre-calibrated sensors - Status LED for sensor operation (green)/malfunction (red)
- Swiss quality product
Gas measuring transmitter KSIM
- The gas measuring transmitter is used to monitor the desired gas concentration
- The gas measurement transmitter is a member of the KIMESSA CANline BUS network, which enables the connection of up to 128 gas sensors and alarm components
- Linear and temperature-compensated digital CANline BUS output signal or 4-20 mA output signal
- 16...30 VDC supply voltage (2-wire, 3-wire supply line or 4-wire for CANline BUS network)
- The gas measurement transmitters are calibrated in the factory to the required measuring range and supplied with a calibration certificate
- All potentiometers and measuring device connections for calibration are accessible from the outside and it is not necessary to open the gas measuring transmitter
- Robust housing (protection class IP 65)
- Stainless and acid-resistant steel housing
- Optional ATEX protection class: Ex II 3G nA IIC T6 Gc
- Swiss quality product